Problem: A polyvinyl chloride resins plant discharges oil into its wastewater. The oil, which is used in the polymerization process, frequently exceeds state limits in the wastewater, which could mean a $53,000-per-day fine. To avoid this, the plant has been metering its discharge from a sump into the public water system in smaller amounts — a costly and inefficient answer. Additionally, the company wants to resell the separated oil, but it is now wasted as part of the discharge.
The plant, which produces 185,000 pounds of resins each year, needs a way to separate and remove the oil from its wastewater.
Limitations: To meet safety, cost and efficiency goals, the plant needed a solution that could run without an operator and be installed without reconfiguring the current wastewater collection-and-discharge system. The solution also had to be low maintenance and long lasting.
Solution: Oil Skimmers Inc., installs a Model 6V Brill™ oil recovery system, which meets the chemical manufacturer’s needs by:
- Fitting into the current wastewater system: Oil Skimmers can customize each installation. In this case, Oil Skimmers creates a mount system to hold the Model 6V at the edge of the sump. The machine’s collection tube is fed through two small holes cut into grates covering the sump.
- Collecting and separating the oil for resale: In a unique anticlogging design, the Model 6V has a specially formulated plastic tube that attracts and collects the waste oil as it floats on top of wastewater. The oil sticks to the outside of the tube, which then passes through a scraper system that removes the oil. The separated oil flows by gravity into a storage drum. The machine then returns the tube to the wastewater for another round of collection.
- Reducing oil in wastewater: The Model 6V can pick up 10 gallons to 60 gallons of oil each hour.
- Allowing independent operation: The Model 6V Brill™ operates independently and is set on a timer to run during the plant’s five-days-a-week operation. If needed, the Model 6V could run 24 hours a day, seven days a week.
- Providing durability: The Model 6V’s internal components are made of high-strength steel and bronze for durability. External parts are made from abrasive-resistant ceramic. The machine has a 25 to 30 year lifespan.
Call or contact us today at 1-800-200-4603, and we’ll find the right system for you.
Reprinted from Chemical Processing
Problem: The biggest challenge confronting Rohm & Haas Corp. in building a wastewater plant for its chemical facility in Elma, WA, was meeting Washington State Department of Ecology limitations on boron of 5 ppm. The Elma plant manufactures sodium borohydride, a versatile chemical used in a variety of applications ranging from the generation of sodium hydrosulfite for reductive bleaching of wood pulp, to the purification of process chemicals. It is used as a pollution control method, to remove heavy metals from wastewater.
Limitations: Some complications contained in the Department of Ecology Waste Discharge Permit are routine, such as BOD, COD , suspended solids, and total oils. Others are specific to the Elma plant, such as boron, zinc from cooling tower treatment, and the ratio of the plant’s flow to the residential discharges. In addition, both the Washington State Department of Ecology and EPA required the plant to submit an “Oil Spill Prevention, Control and Countermeasure Plan.”
Solution: The first step in water pollution control at the Elma plant is collecting and impounding all wastewater from the plant. This is accomplished with three underground sewer systems.
- The first of these sewers connects all chemical drains, sending the discharge to a 15,000 gallon concrete basin.
- The second of the underground sewers collects storm water from all the padded and diked areas of the plant, and sends it to a second, 10,000-gallon concrete basin.
- The third sewer is for sanitary wastewater only, and flows directly to the municipal sewer. The contaminated wastewater and storm water are not suitable for discharge without further processing.
Oil is removed with a Model 6V oil skimmer. The skimmer is designed to be used in either basin and has operated effectively with varying types of oil. The unit operates continuously, skimming oil from the surface as it enters the basin. There is no chance for accidental discharge.
A closed loop of a specially formulated flexible tube floats on the water surface. Oil adheres to its surface, but water is repelled. The skimmer continuously draws the oil-covered tube through scrapers, and returns the clean tube to the water’s surface to gather more oil.
The skimmed oil flows by gravity through the mounting system or a trough to the storage tank. The flexible, floating collector tube is able to snake over and around floating debris to reach the floating oil. It floats up and down with varying liquid levels. The flexible tube flops so that it breaks up crusted oil or grease enabling it to adhere to the tube.
The original plant design called for pH adjustment with sulfuric acid. A circulation system was installed to permit the addition of concentrated acid to the recycle stream from the basin.
Shortly after plant start-up, Rohm & Haas initiated a cost-savings project to use CO2 rather than sulfuric acid for neutralization. In addition, the potential for over-neutralization is reduced, as the minimum possible pH using excess CO2 is about 6. The source for CO2 is a waste gas stream from the hydrogen-generating unit, less than 100 feet from the effluent basins. A sparge nozzle was installed at the bottom of each of the basins to receive the waste gas stream, which is piped directly from the hydrogen plant.
The system uses a flow-through pH sensor and pH transmitter/analyzer to control the amount of CO2 sparged. The pH sensor measures the pH of the flowing aqueous fluid, and in this case, is installed directly in the stream to the holding basins.
The sensor consists of a flow chamber, glass and reference electrodes, temperature compensator, and an ABSjunction box containing a preamplifier. These components are mounted on an ABS back-plate which is clamped to a 2-inch pipe.
Since the signal from the sensor is preamplified, the transmitter/analyzer can be located as far as 3 miles away from the point of measurement. Signal transmission requires only an ordinary four conductor shielded cable.
Non-interacting zero and span controls are used to adjust the output of the unit to any desired range within 0 to 14 pH. This range may involve a span as narrow as two pH units anywhere on the 0-14 pH range.
Evaporation as Final Control
The system requires evaporation as a final control step to meet the 5 ppm limit on boron in the effluent. Based on the operating economics, Rohm & Haas chose a two-stage Spray-Film® vapor compression evaporator. This unit concentrates both process and storm water to the 15-20% total solids range.
This type of evaporator has distinct advantages when handling low to medium boiling point elevation solutions. Energy usage is exceptionally low – typically only 40 Btu per pound of water evaporated.
The solution to be concentrated is sprayed over heated tube bundles and is partially vaporized. The liquid that does not vaporize is re-circulated for further concentration. The vapor is compressed in a vapor compressor and returned to the evaporator module. Here it condenses on the inside of the heating tube bundle, thus causing vaporization of the recirculating solution.
Rohm & Haas has been able to divert the evaporator distillate for use as cooling tower makeup water. This recycle serves a dual purpose, both reducing the plant sewer discharge and the plant raw water requirement. With this latest water conservation project to recycle the evaporator distillate, the plant is one step closer to the zero-discharge level. Presently, only the plant sanitary waste is sent to the municipal sewer.
The evaporator concentrate is collected in one of several fiberglass reinforced plastic (FRP) storage tanks. The composition of the concentrate is primarily sodium carbonate (sodium sulfate when acid neutralization is used) and sodium borate. When sufficient quantity of concentrate has been collected, it is trucked to one of two firms licensed for waste disposal. It is interesting that one of these firms further concentrates the sodium borate and sodium carbonate for use as an additive in commercial fertilizer.
Spill Control Measures
The second area of pollution control involves the system of dikes and curbs around storage tanks, process equipment, product loading area and oil unloading area. All are designed to contain the contents of the respective vessels in the event of a tank rupture or major spill.
Results: Rohm & Haas used evaporation equipment to meet the tight specifications on boron of 5 ppm or less in wastewater effluent. Wastewater processing also includes oil removal to less than 50 ppm and pH adjustment to the 6.0-8.5 range.
Since use of heavy metal compounds in cooling water treatment was restricted, Rohm & Haas substituted a phosphate-based corrosion inhibitor for the commonly used zinc-based system. During the first two years of operation, corrosion rates have been acceptable, ranging from 1 to 2 mils per year.
The Pacific Northwest Pollution Control Association (PNPCA) named Rohm & Haas Corporation as the recipient of its annual “Industrial Pollution Control Award” for accomplishments in pollution control at its new Elma ,WA, facility. Richard Engelbrecht, president of the Water Pollution Control Federation, presented the award to John A. Durrell, Elma Plant Manager, at the 44th Annual PNPCA Meeting.
Rohm & Haas Corporation was awarded one of six State Environmental Excellence Awards for “innovative, state-of-the-art pollution controls” at its Elma plant. Winners were selected by the Washington State Ecological Commission from a number of nominations. Rohm & Haas was nominated for the award by Elma city officials who pointed to Rohm & Haas’s “cooperative, good neighbor attitude” in making the nomination.
Rohm & Haas actively sought to achieve a high degree of pollution control in the planning stages for the Elma plant. Although many of the accomplishments at Elma were preceded at Rohm & Haas’s plant in Danvers, MA, some systems installed were totally innovative and required advancements in state-of-the-art technology. Spill control measures at the plant are exemplary, and serve as a model for others in the industry. The Washington Department of Ecology commended Rohm & Haas for having the most comprehensive system in the area.
No matter what your application needs, Oil Skimmers, Inc. has a system that will manage all your waste oil recovery efforts. Call or contact us today at 1-800-200-4603, and we’ll find the right system for you.